Guide · Warehouse managers · 4 min read · Updated 17 November 2026
Racking Inspection Requirements in the UK Explained
Short answer
BS EN 15635 recommends that steel storage racking is inspected at least every twelve months by a technically competent person, with regular in-house checks in between. Damage is graded green, amber or red, with red meaning the area must be offloaded and isolated immediately. Under PUWER, racking is work equipment and must be kept in a safe condition.
The standard and the law
BS EN 15635 covers the application and maintenance of steel static storage systems, including pallet racking and shelving. It recommends that racking is inspected at least every twelve months by a technically competent person, and that the user appoints someone responsible for storage equipment safety on site.
The Provision and Use of Work Equipment Regulations 1998 treat racking as work equipment. It must be suitable for its purpose, maintained in a safe condition and inspected where damage could create a risk. Following BS EN 15635 is a widely recognised way of showing racking is being managed properly.
The person responsible for storage equipment safety, often called the PRSES, should understand the racking system, its load limits and how to spot damage. They organise in-house inspections, keep records, arrange repairs and make sure staff report damage. In smaller warehouses this might be the warehouse manager. In larger operations it can be a dedicated role supported by trained inspectors on each shift.
Types of inspection
There are three levels of checking. Immediate reporting means every member of staff reports damage as soon as they see it, especially forklift drivers who may cause it. Regular in-house visual inspections are carried out by a trained person on site at intervals set by risk assessment, often weekly or monthly in busy warehouses.
The expert inspection is the annual, detailed check by a technically competent person, often external. They examine every bay, measure damage, check anchors, load notices and accessories, and provide a written report with recommendations.
In-house inspections should follow a simple, consistent route and checklist, so nothing is missed and results can be compared over time. Recording findings on a plan of the racking, bay by bay, makes it easy to see where damage keeps happening. Repeated damage in one aisle often points to a layout problem, such as a tight turn or poor visibility, rather than careless driving alone.
| Inspection | Who carries it out | Typical frequency |
|---|---|---|
| Immediate reporting | All staff, especially truck drivers | As soon as damage is seen |
| In-house visual inspection | Trained person responsible for racking safety | Set by risk assessment, often weekly or monthly |
| Expert inspection | Technically competent inspector | At least every twelve months |
The red, amber and green system
BS EN 15635 grades damage using a traffic light system. Green damage is within acceptable limits and needs recording and monitoring at the next inspection. Amber damage is hazardous but not severe enough for immediate offloading. The area should be offloaded and not reloaded until the damaged component is replaced, with repair arranged as soon as possible.
Red damage is very serious. The affected area must be offloaded immediately and isolated so it cannot be used until repaired. Isolation usually means physical barriers or tape and clear signs. Amber damage that is not repaired within a set period should be treated as red.
- Green: record and monitor at the next inspection
- Amber: offload, do not reload, repair as soon as possible
- Red: offload immediately and isolate until repaired
- Unrepaired amber damage escalates to red
What inspectors look for
Inspectors check uprights for dents, bends and twisting, beams for deflection and damaged connectors, and bracing for bends or missing members. They check that beam locks are fitted, anchors are present and tight, baseplates are intact and frames are plumb.
They also check load notices are present and accurate, that loads do not exceed them, and that pallets are in good condition and correctly placed. Accessories such as pallet supports, mesh decks and upright protectors are checked too.
- Upright damage and plumb
- Beam deflection and connectors
- Beam locks and anchors
- Load notices and actual loads
- Pallet condition and placement
Load notices and changes
BS EN 15635 expects load notices to be displayed on racking showing the safe working loads for beam levels and bays. These should match the manufacturer's data for the configuration installed. Changing beam levels can reduce the capacity of the frames, so load notices must be updated after any reconfiguration.
Keep records of the original design, any changes and inspection reports. They help inspectors and show racking is being managed responsibly.
Overloading is a common finding. Stock changes over time, and heavier products end up on beams designed for lighter loads. Weighing typical pallets and comparing them with the load notices is a quick way to check. If loads have increased, the racking may need stronger beams or different beam levels.
Dealing with damage
Damaged components should be replaced, not straightened or welded, unless the manufacturer approves a repair method. Replacing an upright costs £150–£400 per upright, including offloading and reinstatement.
Fitting upright protectors and end-of-aisle barriers reduces repeat damage. Driver training and good aisle layout help too. We can arrange repairs following an inspection report and confirm one fixed price for the work.
Damage often concentrates at aisle ends and at the lowest beam level, where trucks turn and pallets are placed at speed. Looking at where damage occurs, and why, helps target protection and training. Recording repairs and their cost can also justify spending on barriers, better lighting or wider aisles. Ask the expert inspector to recommend changes that reduce damage, not only to list damaged parts.
Questions people also ask
How often should pallet racking be inspected?
BS EN 15635 recommends an expert inspection at least every twelve months by a technically competent person. In-house visual inspections should be carried out more often, at intervals set by risk assessment. Staff should report damage immediately.
What does red damage mean on racking?
Red damage is very serious. The affected area must be offloaded immediately and isolated so it cannot be used until the damaged component is replaced. It should be clearly marked and barriered.
Can damaged racking be repaired by straightening?
Generally no. Damaged uprights and beams should be replaced with new components. Straightening or welding can weaken steel. Only use repair methods approved by the racking manufacturer.
Written and checked by the Industrial Shelving Installation team. Read our editorial policy.
More guides
How Much Does Pallet Racking Installation Cost in the UK?
Pallet racking supplied and installed in the UK costs £40–£90 per pallet location, and installing customer-supplied racking costs £10–£25 per…
Pallet Racking vs Longspan Shelving: Which Do You Need?
Pallet racking stores palletised goods loaded by forklift, priced at £40–£90 per pallet location supplied and installed. Longspan shelving stores…
Do Mezzanine Floors Need Building Regulations Approval?
Yes, mezzanine floors usually need Building Regulations approval covering structure, fire safety and means of escape. Fire protection such as…
How to Plan a Warehouse Racking Layout
Plan a warehouse racking layout by measuring the clear height and floor area, confirming pallet sizes and weights, choosing truck types to set aisle…
Get a free industrial shelving installation quote
Tell us what you need and we'll come back with a clear price.
Request a quote